[email protected]

(II-1-2) Steel and Iron Materials

specified for the steel grade shall be shown in the certificate. Chapter 2 Page 12 Section 1 Steel Plates, Strips, Sections and Bars II - Part 1 GL 2009 A. In the event of any doubt as to the composition of the products, a product analysis shall be carried out at the API 5L pipe specifications American Piping Products

  • ScopeProcessChemical RequirementsPlate Specification Guide 2015-2016 - ArcelorMittal2015-2016 Plate Steel Specification Guide Page 6 ASTM Specifications continued SPECIFICATION A299 Grade A A299 Grade B A302 Grade A A302 Grade B A302 Grade C A302 Grade D Type of Steel Carbon Carbon Alloy Alloy Alloy Alloy Requirements for Delivery A20 A20 A20 A20 A20 A20 Tensile Strength (ksi) 75/95 80/100 75/95 80/100 80/100 80/100 Yield Strength (Min. ksi)

    Fabrication of Reinforcement - UK CARES

    Table 1 Note 1 In the Grade description B500A, etc., B indicates reinforcing steel. Note 2 Within the ranges given, the grade(s) supplied for notations H and B are at the suppliers discretion. 1.0 Introduction The fabrication of reinforcing steels, into shapes suitable for fixing into the concrete formwork, is normally MATERIALS & GRADESNon-alloy steel and cast steel, free cutting steel < 0.25 %C Annealed 420 1350 0.21 125 1 >= 0.25 %C Annealed 650 1500 0.22 190 2 < 0.55 %C Quenched and tempered 850 1675 0.24 250 3 >= 0.55 %C Annealed 750 1700 0.24 220 4 Quenched and tempered 1000 1900 0.24 300 5 Low alloy steel and cast steel (less than 5% of alloying elements Q235 Steel Q235A Q235B Q235C Q235D Equivalent,

    • Q235 SteelFeatures and ApplicationsData Sheet and SpecificationQ235 Steel EquivalentComparing Steel Plate Gradesweldments, bolting and riveting fabrications. You will find this grade of carbon steel used most often in the construction of buildings, bridges and oil rigs. ABS Grade A, Grade B, Grade ADH36, Grade DH36, and Grade EH36:This steel is used almost exclusively in shipbuilding, especially in the construction of ships, barges, and marine equipment.

      Section 15 Concrete Reinforcement

      2.0 Class A Class A Class B < 2.0 Class B Class C Class C The minimum lap length for a tension splice shall be as required for Class A, B, or C splice, but not less than 1-0:Class A Splice = 1.0 x L d Class B Splice = 1.3 x L d Class C Splice = 1.7 x L d The following Lap Splice Selection Guidelines table is only a recommendation. Steel Grade Equivalents Guide Hillfoot33 rows · Steel Grade Equivalents The table below details similar grades to the most commonly used Steel Tubing - Steel Tubing Supplier - RyersonSteel Tube Shape:Steel Tube Grades/Types:Steel Tube Sizes:Rectangular Steel Tubing:Grades:1008/1010, A500 Gr B/C, HSLA Gr 70 Types:CREW, HREW:Widths 0.5" thru 20"

      What is Rebar? Types and Grades of Steel Reinforcement

      1. Mild Steel Bars Mild steel bars grade-I designated as Fe 410-S or Grade 60. Mild steel bars grade-II designated as Fe-410-o or Grade 40. 2. Medium Tensile Steel Bars designated as Fe- 540-w-ht or Grade 75. Physical Requirement of Mild Steel Bars Table 2:Physical Requirement of Mild Steel BarsEquivalent Grades ALLOY STEELFREE CUTTING STEEL Internal Standard Equivalent Grades BS DIN IS EN SAE/AISI JIS EN15(AM) 216M36 - 40Mn15S12 ENI5(AM) 1137 - EN1A 220Mo7 9SMn28 11C10S25 EN1A 1213 SUM22 EN1APB 220Mo7Pb 9SMnPb36 - EN1APB 12L14 SUM24L EN8M 212M36 - 40C10S18 EN8M 1I46 - SAE1146 - - 40C10S18 EN8M SAE1146 - LOW CARBON STEEL Internal