[email protected]

Basic catalogue - Standards, dimensions and grades

Buttweld Fittings acc. to DIN EN and DIN Cutting and bevelling, tapering, blasting, coating and marking for all requirements according to customer specifications Standards Carbon steels DIN EN Seamless pipes 10216-1 to 4 Welded pipes 10217-1 to 6 Precision steel pipes 10305-1 to 5 DIN Flanges - pipefittingwebDIN Blind flange :25272527:25272527:25272527:2527 :Flat flange for welding (slip on) 2573:25762502:25032503:Welding neck flange 2630 :2630 2631:26322633:26342635:26362637 :2638 2629:26282627:Lapped (lapped joint) flange, Plain collar :26412642:Loose flange and ring for :welding (slip-on flange and plain collar) 26522653:2655

EN 1.0503 Material C45 Steel Equivalent, Properties

EN 1.0503 Material C45 Steel. EN 10083-2 C45 steel (EN 1.0503) is a high strength medium carbon quality steel. Due to poor hardenability, C45 material is generally used in a normalized condition, and when the mechanical properties are required to be high, the quenching and tempering treatment is adopted. The cold deformation plasticity is medium, and the machinability of annealing and EN10028-2 Alloy Steel Plate P265GH|P355GH|16Mo3 - Product Scope Steel plate product available by EN10028-2 standard includes 5 steel grades:P265GH, P295GH, P355GH, 16Mo3, 10CrMo9-10. EN 10028-2 is the European standard that specifies requirements for steel plate and sheet products for pressure equipment made of weld-able non-alloy and alloy steels with elevated temperature properties as specified. EN10216-2 Seamless Steel Boiler Tube - EN10216-2 is specification made for seamless steel tubes for specified elevated temperature purposes as boiler tube, power plants, etc, it has following steel grades:P195GH, P235GH, P265GH, 16Mo3, 14MoV6-3, 13CrMo4-5, 10CrMo9-10, with non-alloy and alloy steel included. EN 10216-2 specifies the technical delivery conditions in 2 test categories for seamless tubes of circular cross section, ANSON is an experienced boiler and pressure steel tube supplier which can offer you EN10216

EN24T Steel Properties

EN24T Steel Properties. EN24T / 817m40. EN24 is usually supplied in the T condition with a tensile strength of 850/1000 N/mm 2. EN24T steel is a popular grade of through-hardening alloy steel due to its excellent machinability in the "T" condition. EN24T is used in components such as gears, shafts, studs and bolts, its hardness is in the range Equivalent Grades ALLOY STEELFREE CUTTING STEEL Internal Standard Equivalent Grades BS DIN IS EN SAE/AISI JIS DIN BS EN AFNOR UNI UNE SS GB A570.36 STKM 12A STKM 12C 1.0038 RSt.37-2 4360 40 C E 24-2 Ne 1311 15 1015 1.0401 C15 080M15 CC12 C15, C16 F.111 1350 15 1020 1.0402 C22 050A20 2C CC20 C20, C21 F.112 1450 20 Material data sheet E195 - SeebergerChemical composition to DIN EN 10305-2 / 10305-3 [In % of the mass] % C Si Mn P S Al max. 0,15 0,35 0,70 0,025 0,025 - Mechanical properties to DIN EN 10305-2 [Minimum values] +C +LC +SR +A +N Rm MPA A % Rm MPA A % Rm MPA Reh MPA A % Rm MPA A % Rm MPA Reh MPA A % 420 6 370 10 370 260 18 290 28 300-440 195 28 Mechanical properties to DIN EN

Materials - Schnorr GmbH

X39 CrMo 17-1 (1.4122):This is a chromium-molybdenum alloyed steel according to DIN EN 10088-2 that can be quenched and tempered. This material grade has also proved very well for the use of heatresistant disc springs. Please bear in mind that both steel grades mentioned are not considered as corrosion-resistant steel grades. RF 100 U centre cuttingfor materials < 48 HRC, centre cutting DIN 6527 L NRf HB Solid car-bide 6,000 - 25,000 3204 106 1132 DIN 6527 L NRf HB Solid car-bide 6,000 - 25,000 3723 106 1132 DIN 6527 L NRf HB Solid car-bide 6,000 - 20,000 3365 106 1132 GS 100 A - roughing end mills with coarse teeth for Al < 600 N/mm², centre cutting DIN 6527 L WR HB Solid car-bide 6,000 - 20,000 3364 106 1133 DIN Sanmac® 4541 Sandvik Materials TechnologyDec 10, 2020 · 1 MPa = 1 N/mm 2 a) R p0.2 and R p1.0 correspond to 0.2% offset and 1.0% offset yield strengths, respectively. b) Based on L 0 = 5.65 S 0 where L 0 is the original gauge length and S 0 the original cross-sectional area.. Impact strength. Due to its austenitic microstructure, Sanmac ® 4541 has very good impact strength both at room temperature and at cryogenic temperatures.

Workpiece materials - Sandvik Coromant

Specific cutting force:350700 N/mm²; Cutting forces, and thus the power required to machine them, are low; The material can be machined with fine-grained, uncoated carbide grades when the Si content is below 7-8%, and with PCD tipped grades for aluminium with higher Si content; Over eutectic Al with higher Si content > 12% is very abrasiveMaterials comparison DIN / EN / ASTMMaterials comparison DIN / EN / ASTM Pipes / tubes Material number EN AStM Non-alloy 1.0254 St 37.0 P235TR1 A 53 Grade A 1.0570 St 52-3 S355J2H (1.0576) -